Solution Summary: Self-Propelled Platform Truck
When using a non-powered platform truck to move heavy loads, a worker must perform heavy pulling or pushing. These movements can cause musculoskeletal disorders (MSDs). A self-propelled platform truck is an engineering control that reduces the stress of pulling or pushing objects during material handling. These powered equipment allow maneuvering of large, heavy objects with minimal effort, and are smaller than traditional forklifts.
Self-propelled platform trucks (figure 1) are used for moving loads too heavy for traditional platform trucks that are non-powered. Depending on models, some of these electric-powered equipment can handle loads up to 1,500 pounds across worksites (figure 2) or up to 1,100 pounds on inclined 8 degrees surfaces (figure 3). These equipment are navigated by hand controls on the back of the truck. As the examples with vendor description below is not a comprehensive list of all existing self-propelled trucks, please visit other manufacturer or vendor websites for equipment suitable to the job's requirements.
Figure 1. Vestil self-propelled platform truck (Source: www.GlobalIndustrial.com)
The Vestil self-propelled powered truck, without the additonal shelves, can handle loads up to 750 pounds. Integral traction drive features a 500W, 24V electric drive motor, (2) 95AH batteries, and an on-board 6 amp battery charger. Ergonomically designed low-hinged handle with pivot-action offers variable speed control, horn, and safety-reverse features. Unit operates up to 2.8 miles per hour (mph) when unloaded, and up to 2.5 mph when fully loaded. Standard features include automatic braking, automatic parking brake, free-wheel lever for manual operation, and battery gauge level. Electronics are enclosed in splash-proof casing for safety. Rolls smoothly on two 9" solid foam steer wheels and two 10-¼" solid foam load wheels. 14" deck height and non-slip tread-plate surface.
Moto-Cart Self-Propelled Battery Powered Platform Truck
Figure 2. Moto-Cart self-propelled platform truck (Source: www.markpack.com)
The Moto-Cart is a battery operated self-propelled electric platform truck. This unique cart increases productivity and reduces injuries caused by pushing and pulling non-powered carts. This flexible vehicle can travel over carpeting, tile, or any hard surface, go in and out of elevators and handle 1500 pounds on level surface and 1000 pounds on inclines up to 6 degrees. Safety features include: horn, flashing reverse mode switch which flashes yellow, automatic braking, automatic parking brake, emergency stop switch, and will not operate when parking brake is off, when plugged in to charge, or if the throttle is faulty. Travel distance is approximately 15 miles on a charge.
When using a traditional platform truck to transport heavy loads, a worker must perform heavy pulling or pushing. Heavy pulling and pushing heavy objects can cause disc herniation, muscle strain, and other MSDs. A low back disc herniates when there are excessive loads are placed on the spine. Overworking the muscles can also result in strains. Using self-propelled platform trucks may reduce the risk of disc herniation, muscle strains, and other MSDs associated with pulling and pushing.
How Risks are Reduced:
Self-propelled platform trucks eliminate the manual pushing and pulling that is required with traditional platform trucks. Instead, the self-propelled mechanism uses power generated from an electric motor to move heavy loads.
There have not been independent published studies measuring the effect of self-propelled platform trucks on the incidence of low back disorders. However, studies have shown an association between manual materials handling and low back pain. (Kuiper et al. 1999; van der Molen et al. 2005). Self-propelled platform trucks reduce the amount of manual materials handling and therefore may reduce the incidence of low back pain.
Operators of self-propelled platform trucks also need to consider the weight of the equipment with the material load when maneuvering across the job sites as floor hole covers, temporary wood ramps or flooring structural supporting members have load limits. In addition, it is recommended users follow all manufacturer guidelines before using this equipment to ensure worker safety and compliance with applicable local, state or federal regulations.
Small, hard surfaced wheels may be a challenge while operating on the typically congested and debris, strewn floor at most construction job sites. A pneumatic type wheel may solve this challenge.
Jean Christophe Le, MPH - CPWR The Center for Construction Research and Training
- General Labor
- Load, unload and distribute construction materials
To obtain information, visit Vestil Self-Propelled Battery Powered Platform Trucks and Wesco Self-Propelled Battery Powered Platform Trucks or contact 1-888-978-7759
To obtain information, visit Moto-Cart Self Propelled Platform Truck or contact 1-888-874-5454