Solution Summary: Tool Handle Wraps
A tool handle wrap is an engineering control that can help reduce musculoskeletal disorders (MSD) from hand-arm vibration. They are made from viscoelastic materials that are designed to dampen vibration from power tools. They can be available in long narrow strips, heat shrink tubing, or larger rectangular sheets. An adhesive is used to keep the wrap on the tool. Typically, a 44 inch strip is long enough to wrap an average-sized handle.
Tool handle wraps are viscoelastic materials that are designed to dampen vibration from power tools. They are available in long narrow strips, heat shrink tubing, or larger rectangular sheets. An adhesive is used to keep the wrap on the tool. Typically, a 44 inch strip is long enough to wrap an average-sized handle. Materials vary in thickness from 1/8 to 1/4 inch.
Figure 1. Tool handle wraps used on small hand tools.
Figure 2. Tool handle wraps on a large mechanical tool.
It is recommended to purchase bulk quantities of tool handle wrap because the wrap becomes ineffective at dampening vibration after use, and therefore must be replaced frequently to remain effective. There is a lack of data available that details which vibration frequencies are dampened when using tool handle wraps. For these reasons, tool handle wraps should be used as a last resort or temporary solution until reduced vibration tools can be purchased.
Stressful hand and wrist activity and hand-arm vibration can cause musculoskeletal disorders (MSDs) such as muscle strains; tendonitis, which is inflammation of elbow and wrist tendons; or carpal tunnel syndrome, which is compression of a wrist nerve, resulting in finger numbness and loss of hand strength. Tool handle wraps can reduce stressful hand and wrist activity and hand-arm vibration by increasing the contact area between the hand and tool handle for handles with sharp edges to reduce uncomfortable contact stresses.
How Risks are Reduced:
Tool handle wraps are designed to reduce the intensity of vibration transmitted from a tool to the hand and arm. Also, tool handle wraps can increase the contact area between the hand and tool handle for handles with sharp edges. These wraps can reduce exposure to uncomfortable contact stresses to the hand. Tool wraps can also improve comfort when holding tools with metal handles, which can get cold.
Some companies report that vibration dampening tool handle wraps can protect the hands from 55% of the vibration energy created by the tool.
There have not been any independent studies on tool handle wraps. A disadvantage of tool handle wraps is that handle diameter increases, which may increase grip force. Thus, safety and health experts do not agree that the possible advantages of using tool handle wraps outweighs the disadvantages.
Effects on Productivity:
Tool handle wraps may increase or decrease productivity, but protecting the hands from injury while handling/operating tools.
Some safety and health experts do not recommend tool handle wraps because they increase tool handle diameter and may not dampen the impact of harmful hand-arm vibration frequencies. When tool handle diameters are too thick, more forceful exertions are required to operate the tool. Handle diameter for single-handed tools, such as a screwdriver should be between 1.25 and 2 inches for power tasks (high force), and between 0.25 and 0.5 inches for precision tasks (low force). See the Ergonomic Hand Tools solution page for more detailed hand tool guidelines. Instead of using tool handle wraps, health and safety experts recommend that workers use reduced vibration tools or anti-vibration gloves.
Dan Anton, PT, PhD, ATC – Eastern Washington University, and Alysha Meyers, PhD – University of Iowa
- Construct suspended ceiling interior systems
- Frame floors, walls, ceiling, stairs and roofs using wood and/or metal studs and door bucks
- Install cabinets, countertops and moldings
- Install doors, windows and associated hardware
- Remove commercial carpet
- Drywall, Glass & Floor Coverings
- Climb poles and structures
- Install and maintain electrical control systems
- Install and maintain fixtures, lights, motors and pumps
- Install and maintain temporary wiring systems on construction sites
- Install and repair high voltage lines, transformers and switches
- Install interior wiring systems
- Pull wire through conduits
- Splice and connect wiring systems
- Work with or remove old wiring
- Excavation & Demolition
- General Labor
- Heavy Equipment
- Maintain heavy equipment
- Insulation & Lagging
- Access piping in trenches and confined spaces
- Attach insulation with tape, staples, glue, wire and bands
- Blow and place insulation
- Inspect and use scaffolds and ladders
- Install and apply fire stop products
- Install finished insulation around duct, pipes, tanks, vessels and mechanical equipment
- Maintain and remove old insulation including asbestos
- Spray fireproofing onto columns and beams
- Masonry, Tile, Cement & Plaster
- Apply caulk, sealants and waterproofing materials
- Chip, scrape and grind surfaces, or joints
- Clean surfaces
- Cut bricks, blocks, stone, concrete, tile or terrazzo
- Drill holes and install reinforcing rods and anchors
- Pipes & Vessels
- Assemble pipes, tubing and fittings
- Cut and drill holes in structures prior to pipe installation
- Cut, thread, hammer and bend pipes and vessel tubes
- Disassemble and remove damaged or worn pipe
- Lay and align pipe in trenches
- Reinforced Concrete
- Residential Construction
- Apply caulk, sealants and waterproofing materials
- Assemble forms and add reinforcing
- Cut boards and panels
- Install and finish flooring
- Install electrical systems
- Install exterior siding
- Install framing and roof trusses
- Install modular or prefabricated components
- Install plumbing
- Install roof and exterior sheathing and sub-floors
- Install roofing shingles or tiles
- Install wood, metal or engineered floor and ceiling beams
- Paint interior and exterior walls, ceilings, trim, etc.
- Pour, pump and vibrate concrete
- Sheet Metal & HVAC
- Assemble fittings and fasten seams and joints using hand and power tools
- Install heating and air conditioning duct hangers and ductwork
- Install risers
- Layout, shear, drill and punch holes in metal
- Structural Steel
- Dismantle or demolish metal structures
- Drill, grind and saw materials
- Fabricate metal structures in shop and field
- Weld, plasma cut, air-arc and flame cut metal