A pre-blended mortar and grout delivery system utilizes gravity to deliver grout into the masonry wall.
Hazard Analysis — Silica
Workers who mix concrete may be exposed to silica.
Inhaling crystalline silica can lead to serious, sometimes fatal illnesses including silicosis, lung cancer, tuberculosis, and chronic obstructive pulmonary disease (COPD). When workers breathe in dust containing silica the lung tissue reacts by developing fibrotic nodules and scarring around the trapped silica particles. This fibrotic condition of the lung is called silicosis. If the nodules become too large, breathing becomes difficult and death may result. Silicosis may develop after very short periods of high exposure, but more commonly it develops after many years of lower levels of exposure. There is no cure for silicosis.
Initially, workers with silicosis may have no symptoms. As silicosis progresses, they may experience difficulty breathing and other chest symptoms such as a cough. There are three types of silicosis:
- Chronic silicosis, which usually occurs after 10 or more years of exposure to crystalline silica at relatively low concentrations;
- Accelerated silicosis, which results from exposure to high concentrations of crystalline silica and develops 5 to 10 years after the initial exposure; and
- Acute silicosis, which occurs where exposure concentrations are the highest and can cause symptoms to develop within a few weeks to 4 or 5 years after the initial exposure.
In 1996, the World Health Organization – International Agency on Cancer Research (IARC) changed its classification of crystalline silica from a probable human carcinogen to a known human carcinogen. In 2009, IARC reaffirmed its position noting “[an] increased risk of lung cancer was observed across various industries and processes.”
Exposure to silica has also been linked to renal disease and rheumatoid arthritis.
Work Safely with Silica” at www.silica-safe.org provides information needed to assess the risk, determine if a material contains silica, and an on-line tool to create a job hazard analysis and plan for controlling exposures.
To determine if your worksite has high exposures to silica during these operations, you should: see if the materials you are using contain silica (materials or products containing more than 0.1% silica must be labeled) and measure exposure.
Regulations & Standards:
OSHA has a Permissible Exposure Limit (PEL) for exposure to respirable crystalline silica of 50 micrograms per cubic meter of air (µg/m3) based on an 8-hour time weighted average. OSHA also requires hazard communications training for workers exposed to crystalline silica, as well as a respiratory protection program until engineering controls are implemented.
In September 2008, CalOSHA issued a standard “Control of Employee Exposures from Dust-Generating Operations Conducted on Concrete or Masonry Materials.”
In December, 2004, New Jersey signed a law prohibiting the dry cutting and dry grinding of masonry.
NIOSH recommends an exposure limit lower than the OSHA PEL. The NIOSH Recommended Exposure Limit (REL), published in 1974, is 0.05 mg/m3 based on a time-weighted average for up to 10 hours.
The American Conference of Industrial Hygienists (ACGIH) recommends a Threshold Limit Value of 0.025 mg/m3 based on an 8-hour time-weighted average.
Federal OSHA Standards are enforced by the U.S. Department of Labor in 26 states. There are currently 22 states and jurisdictions operating complete State plans (covering both the private sector and state and local government employees) and 5 - Connecticut, Illinois, New Jersey, New York and the Virgin Islands - which cover public employees only. If you are working in one of those states or jurisdictions you should ensure that you are complying with their requirements.
One study, “A case-control study of airways obstruction among construction workers”, examined occupational exposures to vapors, gases, dusts and fumes (VGDF) among older construction workers between 1997 and 2013, comparing 834 workers with COPD and 1,243 controls. Approximately 18% (95% CI=2-24%) of COPD in this population can be attributed to workplace exposures associated with construction tasks. After adjusting for smoking habits in this population, the study also revealed among construction workers who never smoked, 32% (95% CI=6-42%) of COPD was attributable to the workplace.
BIM is a concept that offers software technology application (app) that integrates digital building information for hazard identification and safety planning. It can virtual map a project lifecycle from design through procurement, construction, operation, and maintenance.
The Last Planner® System is a production planning and control system designed to produce predictable work flow and improve project performance across the design, construction and commissioning stages of construction projects.
Personal Protective Equipment
A respiratory protection program addresses exposures to airborne dust, engineered nanomaterials, and chemical exposures as well as implementing and evaluating other effective exposure control measures.